卧式东莞拌料机厂家说明

　　百度“中恒东莞拌料机厂家”，

　　性价比至上 品质为上 服务至上

　　电箱接法:1，3，5，9，2，7，9，8，6，8，9

　　中恒东莞拌料机厂家特点

　　1、加热干燥型采用双层U桶体设计，内壁为全不锈钢材质；（订购机型）

　　2、采用导热油为加热介质，热量均匀，方便控制；

　　3、全不锈钢中心轴及“S”形桨叶，坚固耐用，均化效果好；

　　4、选用名厂电机及减速机，出力大，性能稳定；

　　5、可订购螺旋上料机配套，省去加料平台，安全快捷又方便；

　　6、可按客户要求手动或气动型出料口；

　　7、干燥搅拌二合一，关闭“加热开关”即可用于物料均化用途；

　　6、多重安全保护装置，确保操作者用机器的安全。

　　8、也可按客户使用要求，选择碳钢材料制作，节省投资；

　　9、料桶与原料接触部份均采用不锈钢，无集料死角，清料容易。

　　注意:卧式搅拌机开机前减速机内请加齿轮油否则将会导致齿轮损坏（缺少齿轮油不在保修范围之内），如有加热功能，请加入导热油方可使用加热功能，否则将会导致发热管干烧损坏（干烧损坏不在保修范围之内）。

　　中恒东莞拌料机厂家使用方法:

　　开机前请确认电机转向正确（正时针旋转）

　　一、电机运转:电源采用3相四线制，需接零线。(R火线S火线T火线N零线)接通后，红色电源指示灯亮。

　　1、 电机档位开关置于自动档时，定时器工作，设置好所需搅拌时间（可设定S秒M分H小时不同时间）后，按下绿色电机运转按钮，定时器即开始计时，电机运转指示灯亮，到达设定的时间后实现无人自动关机；

　　2、 电机档位开关置于手动挡时，定时器时间显示但不控制电机运转时间，按下绿色电机运转按钮开机后需有专人守候，待物料搅拌好后手动关机。

　　3、 电机档位开关置于停止位置，电机，定时器均不工作。

　　4、 本机型利用左右两片“S”型桨叶上下左右同时翻滚从而达到混料均匀的目的；投物料时，为了更好更快的达到均匀的目的，请不要几种不同的物料中的一种全部投完再投其他物料，应当根据不同的比例相互错开投料；加料时请勿满桶料加至没过桨叶为理想搅拌状态。

　　二、加热功能使用方法（有此功能适用）:将温度设定好后再将开关打开。由于内部电路设置与电机连锁功能，以防止电机不工作，温度过高将物料损坏，使用加热功能时，先将马达启动。

　　加热档位开关置于启动时，温度控制器工作，加热系统正常工作，当温度达到设置值时，发热管自动关闭，待温度降至设置值以下，加热系统重新工作。

　　中恒东莞拌料机厂家保养注意事项:机器检查、维修或者长期不使用请关闭总电源。定期检查减速机内齿轮油，新机3个月更换一次，以后每半年更换一次；两边轴承应1个月加一次黄油。每天开机前检查导热油（选购导热油时请使用正品名厂，防止沸点过低容易积碳损坏发热管。加热机型外部较热，请留意高温部位，以免烫伤，更不要将物料置于桶壁周围，以免引起火灾。机器开动时切勿将手脚等伸入机器内部，顶部电机位置，以及加热系统附近以防发生危险。如发生危险事故，本公司概不承担任何责任。

　　Horizontal plastic mixer Help

　　Baidu search for "the ZHONG HENG plastic mixer", into the company's Web site reference Contact 1,3,5,9,2,7,9,8,6,8,9

　　Online customer service, TKS! !

　　The plastic auxiliary navigator ------ Dongguan ZHONG HENG Plastic Machinery

　　Price first quality service is the first

　　Note: horizontal mixer before starting the reducer please add gear oil otherwise it will lead to gear damage (lack of gear oil is not covered under warranty), if any heating function, please join conducting oil before using the heating function, otherwise it will lead to The heat pipe dry damaged (dry damage is not covered under warranty).

　　The constant plastic mixer using the method:

　　Verify before starting motor turn right (positive clockwise rotation)

　　Motor running: power three-phase four-wire system, must be connected to the zero line. (R FireWire FireWire FireWire S T N zero line) is connected, the red power indicator light.

　　1 the motor stalls switch to the automatic transmission, the timer is set after the required set S seconds M sub H hours stirring time (at different times), the green motor operation button is pressed, the timer starts motor operation indicator light, to achieve unmanned automatic shutdown after the set time is reached;

　　2 the motor stalls switch to the manual transmission, timer time display but does not control the motor running time, press the green motor operation button boot someone waiting to be agitated manually shutdown.

　　3, motor stall switch to the stop position, the motor, the timer is not working.

　　4, the models around about two "S" shaped blade up and down so as to achieve the purpose of mixing uniformity while tumbling; cast material, in order to achieve better and faster uniform purpose, please do several different materials all kind of casting their reinvested other materials should be staggered depending on the proportion of feed; Do not bucketful material feeding plus to not over-stirring paddle ideal.

　　(This feature is available): heating function use the switch to open the set temperature and then. Due to the internal circuit chain set with motor function to prevent the motor does not work, the temperature is too high, the material damage, using the heating function, the first motor start.

　　Heated stalls switch is in the startup, temperature controller, heating systems work properly, automatically shut down when the temperature reaches the set value, the heat pipe, when the temperature drops below the set value, the heating system to work again.

　　The constant plastic mixer characteristics

　　Heating and drying double U barrel design, the inner wall of full stainless steel; (order models)

　　2, the use of heat-conducting oil as the heating medium, heat are convenient control;

　　3, full stainless steel center shaft and the S-shaped blades, durable, homogenizing effect;

　　4, the choice of name factory motor and reducer, large output, stable performance;

　　5 Order Screw Feeder supporting, eliminating the need for the feeding platform, safe, efficient and convenient;

　　6, customers can request a manual or pneumatic discharge port;

　　7, dry stirring two-in-one, turn off the heat switch "can be used for material homogenization purposes;

　　6, multiple security devices to ensure the safety of the operator to use the machine.

　　8, also according to customer requirements, select the carbon steel materials, saving investment;

　　9, drums and raw material contact part are made of stainless steel, aggregates dead ends, clear material easily.

　　In constant plastic mixer Maintenance Notes: machine inspection, maintenance or long-term use, please turn off the main power. Reducer, gear oil, new machines regularly checked 3 months to replace once every six months thereafter replaced once; should be a plus butter on both sides of the bearing. Daily to boot check before conducting oil use positive Name (optional conducting oil plant, to prevent boiling point, low easy to coke damage to the heat pipe. Heating models external heat, please pay attention to the high-temperature parts, so as not to burn, let the material set Tongbi around, so as not to cause a fire and not to the machine running the hands and feet stuck inside the machine, near the top of the motor position, as well as the heating system to avoid any danger. dangerous accident occurs, the Company does not assume any responsibility.

　　我们将24小时为您提供最优质的服务！！！

　　我们的工程师经过多种技术培训，他们有精湛的技术良好的作风，协诚为您们服务！！！

　　了解更多请登录我们的网页（如下）:

　　联系我们:

　　东莞市寮步中恒塑胶机械厂

　　诚信通:zhonghengjx

　　我们公司有勇于挑战新难度，刻服困难的信心和决心。让客户对我们更有信心和更放心购买和使用我司产品。如有需要，我们可以随时到贵司拜访、与您一起讨论.