手感漆油墨

　　概述:手感漆专用油墨是采用高质改性树脂和高级颜料经过细制研磨加工组合而成，具有遮盖力强、附着力佳、流平性好等特点。

　　适用范围:手感漆专用油墨各种喷过手感漆、橡胶漆、弹性漆的工件表面丝印、移印。

　　印刷:

　　选用网目为250-350目的网板。

　　1．用配套专用稀释剂开油

　　2．用718洗网水洗网。

　　3．添加10%的配套硬化剂增加附着力,提高产品的通用性和墨层硬度。

　　干燥时间:

　　表干时间自然挥发5-10分钟，实干时间在添加10%硬化剂，必需烘烤干燥65℃烘烤60分钟；80℃烘烤30分钟；后达最佳性能；

　　测试（完全干燥后）:

　　1．3M胶纸粘在画有百格的油墨表面45度角迅速拉起没异状。

　　2．500克力橡皮耐磨60次，耐酒精50次以上。

　　测试方法（完全干燥后）:

　　1、3m胶纸粘在画有百格的油墨表面，45度角迅速拉起不脱油;

　　2、纯度99%的工业酒精，一千克砝码用棉布包住在油墨表面，以水平力来回拉200次无脱色;

　　3、耐磨:橡皮擦500g力水平来回擦300次。

　　使用方法:

　　1．建议用我公司专用稀释剂进行稀释，不建议使用783慢干稀释剂稀释，使用前应充分搅拌，用后随时密封。

　　2．搅拌时加本公司配套开油水10-12%，稀释到印刷适合粘度，移印稀释使用移印专用稀释剂；用718洗网水清洗。

　　3．不得与其它类型油墨混合使用，否则容易出现其他附着力，化学反应等不良现象。

　　4.加入固化剂的油墨使用时限为8小时，过期请弃用，剩余油墨不可回收

　　注意事项:

　　1．各种承印物料的外观相似，但可能会是不同的材料，客户需先试印，确其符合要求后，再批量生产。

　　2．在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可;

　　3．环境温度过高，将会影响油墨原有质量。白色超越150都会变色，烘烤时请用木质材料垫底进行烘烤，不得直接接触铁

　　4．根据气候变化，请远离火源，阴暗处15度-30度环境下存放

　　Brand: but MY name: feel paint inks Numbers: 65496

　　Feel paint inks

　　Summary:

　　Feel special ink is USES the high-grade paint modified resin and senior pigment after fine grinding process of a combination of strong power, has covered, adhesion, good flow ping sex is good wait for a characteristic.

　　Suitable for: feel special ink spray paint of paint, feel a paint and elastic rubber paint surface of workpiece printing, pad printing.

　　Printing:

　　Choose for 250 350 mesh screen purpose.

　　1. With matching special thinner, open oil

　　2. Wash washing nets with 718 net.

　　3. Add 10% of form a complete set, improve product increase adhesion stiffening agent the versatility and ink layer hardness.

　　Drying time:

　　Dry time table natural volatilize 5-10 minutes, action in time added 10%, must bake stiffening agent 65 ℃ dry baking 60 minutes; 80 ℃ bake 30 minutes; To best performance after;

　　Test (dry) :

　　1.3 M tape stuck in the picture has's ink surface 45 degree Angle quickly pull up no different shape.

　　2.500 g force rubber wear-resisting 60 times more than 50 times, resistance to alcohol.

　　Test method (dry) :

　　1, 3 m stuck in the picture has the tape's ink surface, the 45 º Angle quickly pull up not to take off the oil;

　　2 and purity, 99% of industrial alcohol, a kilogram of Jordan farmar cover with cotton cloth in ink surface to pull back and forth horizontal force 200 times without decoloring;

　　3, wear-resisting: the eraser 500 g force level wipe 300 times back and forth.

　　Method of use:

　　1. The proposal with my company special thinner to dilute, not recommended dry thinners diluted 783 slow, before the use should be fully mixing, use at any time after sealing.

　　2. Add the company supporting stirring open 10 to 12%, oil and water dilute the printing for viscosity, pad printing dilution use moving printing special thinner,; Use clean water to wash the nets 718.

　　3. Not with other kinds of printing ink mixed use, otherwise easy to have other adhesion, chemical reactions and other bad phenomenon.

　　4. Add hardener inks use time limit for 8 hours, please not used, the remaining expired ink not recycling

　　Note:

　　1. All kinds of printing material appearance similar, but may be of different material, customers are required to meet the requirements of the ShiYin, indeed, its, then batch production.

　　2. In moving printing process, such as a wire drawing or away, can be appropriately to add some slow dry paste can;

　　3. Environmental temperature is too high, will influence the quality of the original ink. White will change color, roasted beyond 150 when please use woodiness material bottom, and may not directly contact roast iron

　　4. According to climate change, please away from fire, the shadows 15 degrees-30 degrees environment for