常州环保设备玻璃钢防爆风机

名称:常州环保设备玻璃钢防爆风机

供应商:常州邦亿环保科技有限公司

价格:面议

最小起订量:1/台

地址:常州市钟楼区龙城大道2039号

手机:15861888596

联系人:王经理 (请说在中科商务网上看到)

产品编号:126680853

更新时间:2021-03-27

发布者IP:49.80.120.139

详细说明

  常州玻璃钢防爆风机------常州邦亿环保科技有限公司坐落于江苏常州,是一家集设计、研发、制造、销售、施工、售后服务于一体的综合型废气处理公司。

  公司在成立之时就确定了以人为本,以科技促进发展的理念,始终以“立足环保事业,智力节能减排,改善生态环境”为使命,围绕公司主营业务履行社会责任,严格确立在任何时间都能站在客户的角度、让我们的客户花最少的钱做最优质的工程,并以优质的服务和满意的治理效果赢得了广大客户的认可。

  Changzhou Bang billion environmental protection technology Co., Ltd. is located in Changzhou, Jiangsu. It is a comprehensive exhaust treatment company integrating design, research and development, manufacturing, sales, construction and after-sales service.

  The company is determined in the people-oriented, to promote the development of science and technology philosophy, has always been to "based on the environmental protection, intelligence, energy saving and emission reduction, improving the ecological environment" for the mission, around the main business of the company to fulfill social responsibility, strict establishment can stand in the customer's point of view, let our customers spend the least money the quality of the project at any time, and quality service and satisfactory control effect has won the recognition of our customers.

  防爆离心风机可作为一般工程、易燃易爆仓库、隧道、窑洞及大型建筑物的室内通风换气,输送空气和其他自然的、对人体无害的、对钢材无腐蚀性的气体。气体内不许有粘性物质,所含尘土及硬质颗粒物不大于150MG/m3。气体温度不得超过130°。

  防爆离心风机适用于输送易燃易爆性气体,防爆性能已通过国家防爆电器产品质量监督检验中心检测,可安全适用于石油、化工、天然气等生产防爆气体等特殊环境的通风换气。

  The explosion-proof centrifugal fan can be used for indoor ventilation and ventilation of general engineering, flammable and explosive storehouse, tunnel, cave dwelling and large building, conveying air and other natural, harmless and harmless gases to steel. There is no sticky substance in the gas, and the dust and hard particles are not more than 150MG/m3. The temperature of the gas should not exceed 130 degrees.

  The explosion-proof centrifugal fan is suitable for conveying inflammable and explosive gases, and the explosion-proof performance has been tested by the national explosion-proof electrical product quality supervision and inspection center, which is safe and suitable for ventilation and ventilation in special environment such as petroleum, chemical industry, natural gas and other explosion-proof gases.

  常州玻璃钢防爆风机  结构组成

  防爆离心风机主要由:叶轮、机壳、转子、轴承四大部分组成。叶轮是产生风压和传递能量的主要作功部件;机壳主要用来引入气体和排出气体,同时将气体的部分动能变为压力能;轴承用来连接电机和风机,传递力矩。

  机壳:由钢板制成坚固可靠,可为分整体式和半开式,半开式便于检修。

  叶轮:由叶片、曲线型前盘和平板后盘组成。

  转子:应做过静平衡和动平衡,保证转动平稳,性能良好。

  传动部分:有主轴、轴承箱、滚动轴承及皮带轮(或联轴器)组成。防爆离心风机。

  Structure composition

  The explosion-proof centrifugal fan is mainly composed of four main parts: impeller, machine shell, rotor and bearing. Impeller is the main component for generating wind pressure and transmitting energy, and the shell is mainly used to introduce gas and exhaust gas, and at the same time, partial kinetic energy of gas is changed into pressure energy. The bearing is used to connect motor and fan to transmit torque.

  Shell: the steel plate is made of solid and reliable. It can be divided into whole and half open type, and the semi open type is easy to repair.

  Impeller: it is made up of blade, curved front disc and plate rear disc.

  Rotor: the static balance and dynamic balance should be done to ensure that the rotation is stable and the performance is good.

  Transmission part: the main shaft, the bearing box, the rolling bearing and the pulley (or coupling). Explosion-proof centrifugal fan.

  玻璃钢防爆风机使用说明

  1.检查出风门是否微开;

  2.检查各部位的运转间隙是否在规定范围内,转动部位与固定部位有无碰撞及摩擦现象,紧固件连接是否完好,设备管道有无密封;将离心风机进风门关闭;

  3.检查润滑部位润滑油、脂是否合适;

  4.按“启动”按钮,接通电源启动高压离心风机;

  5.徐徐开封启进风口到所需大小,严密监视风机震动及声响,发现异常立即停车处理;

  6.运行中严密监视风机运转电流,电流过大进必须调整负荷来减少电流数,如果通过调整负载不能解决电流过大现象时,必须停车对风机传动系统进行彻底检查;

  7.运行中应经常检查各轴承温度,一般轴承温升≤400C,轴承表面温度≤700C;温升或表温急剧升高时应立即停车处理。

  Instructions

  1. check out the door is ajar;

  2., check whether the running clearance of each part is within the prescribed range, whether there is any collision and friction between the rotating part and the fixed part, whether the fastener connection is intact, whether the equipment pipe is sealed or not, and close the inlet of the centrifugal fan.

  3. check whether the lubricating oil and grease in the lubricating parts are suitable.

  4. press the "start" button, connect the power to start the high pressure centrifugal fan;

  5. the size of the opening from the opening of the opening to the tuyere, the vibration and sound of the fan is closely monitored, and the abnormal parking is found immediately.

  6., we must closely monitor the running current of the fan in operation. If the current is too large, we must adjust the load to reduce the number of current. If we can't solve the problem of overcurrent by adjusting the load, we must stop and check the fan drive system thoroughly.

  Should always check the temperature of each bearing 7. operation, the general bearing temperature rise is less than or equal to 400C, the bearing surface temperature is less than or equal to 700C; should immediately stop processing the temperature rise or the surface temperature increased sharply when the.