服务中心已遍及华北、华东和华南等地区。主要负责百达翡丽、爱彼、江诗丹顿、芝柏、宝玑、宝珀、朗格、劳力士、积家、卡地亚、欧米茄、万国、浪琴等国内外大小五十多个手表品牌的售后维修工作.专业的维修技术、透明的维修价格、当面检测维修定价、立等可取的维修效率。电话预约可享9折优惠！专业专注，专心服务!让时间鉴定品质!瑞亨名表维修中心，您身边的手表养护专家!

　　________________________________________________________________________________________________________________

　　________________________________________________________________________________________________________________

　　当把手表维修这些问题都检查出来并加以排除后，再用测试机测试，测得各项数据平均值都在标准值内，即表示手表可以准确的运行了，最后若是自动上炼表，可再放于多方位测试机上测时，了解在多方位测试下，时间是否运转精准，并了解表的自动上炼是否没有问题。一切程序都通过后，就大功告成了。我们将有关与手表走时不准的解决方法稍加整理，发现大致上可归结出以下九种原因，零件缺乏时再做修复。手表走时不准测试(1)如遇正面反面3点方向时间据差距太大(方向差)。方法:用摆轮平衡器测试，藉由摆轮旋转来得知摆轮圆径是否均重，如有某方位较重将减轻重量，来达到摆轮圆径均重。(2)摆轮车心太短小油盘会碰到马仔嘴，造成摆轮不平衡。方法:换车心或摆轮整组换掉，或将受石反面装。(3)小油盘松动导致测试值无法稳定。方法:将小油盘取下加以固定(切勿用胶水固定)。(4)车心如遇异常磨损造成铁锤型(头大身细)导致摆轮不平衡。方法:修饰车心，修饰完要将车心打亮(要注意不能导致车心太细)。(5)洗油后轮系如无法适当释放力道原因:1.干净度不够2.齿轮上下间隙太大3.齿轮芯磨损导致左右间隙太大4.上下铜质座磨损导致 左右间隙太大。方法:1.重新清洗2.调整上下宝石座3.换齿轮4.将磨损部份修复。(6)游丝乱掉原因:1.外力影响2.受石油外漏导致游丝沾粘住3.游丝受磁。方法:1.调整游丝2.清洗游丝3.退磁。(7)发条无法正常释放力道原因:1.油太干2.生锈3.弹性疲乏。方法:1. 清洗干净重新加油2.将发条取出重新打亮再上油3.换新发条。(8)自动机芯发条打滑。方法:取出发条，将发条盒壁磨粗或是用特制的发条油。(9)马仔脚与五番车接合点如有误差导致力道不够，使摆轮无法正常运转。方法:调整马仔脚到适当位置。以上这些问题都检查出来并加以排除后，再用测试机测试，测得各项数据平均值都在标准值内，即表示手表可以准确的运行了，最后若是自动上炼表，可再放于多方位测试机上测时，了解在多方位测试下，时间是否运转精准，并了解表的自动上炼是否没有问题。一切程序都通过后，就大功告成了。When the watch repair these problems are checked out and ruled out, and then the test machine test, the average value of all measured data in standard value, that watch can accurate operation, finally if the automatic mixing table, can be placed in the multi position test machine measurement, understanding in many aspects the test time is running, accurate, and understand the table of the automatic mixing is no problem. All procedures are passed, will be accomplished. we will be related to the watch travel time are not allowed to solve the solution with a little finishing, found generally can be attributed to the following nine reasons, when the lack of parts to do repair. watch travel time is not allowed to test (1) in the case of 3 points in the direction of the negative side of the gap is too large (Fang Xiangcha). Methods: the test wheel balancer, balance wheel rotation by that wheel diameter are heavy, if there is a range of heavier will reduce weight, to achieve a circular size weight. (2) a car was too short encounter by pan mouth, caused by wheel imbalance. Methods: to balance the whole group of heart or replaced, or will be affected by the negative charge of stone. (3) value to the small oil pan due to loose stability test. Methods: take the small oil pan to be fixed (not fixed with glue). (4) in case of abnormal heart car caused by wear hammer type (head body fine) leads to imbalance of balance. Method: modify the heart of the car, finishing to the heart of the car (to pay attention can not lead to the heart of the car is too thin). (5) after the train if not properly wash oil release force reasons: 1 clean enough 2 gear on 3 core gear gap is too large due to wear around the gap is too large 4 seat wear under copper lead around the gap is too large. method: 1 to clean the 2 adjustment of the gem seat 3 change gear 4 will wear part of the repair. (6): 1 gossamer mess force affected 2 oil leakage caused by the magnetic dip stick 3 gossamer gossamer. Methods: 1 adjust the hairspring 2 cleaning hairspring 3 demagnetization. (7) cannot be released spring force: 1 oil too dry 2 rusty 3 elastic fatigue. Methods: 1 clean gas will take 2 to spring to play again 3 new spring light oil. (8) automatic movement of the spring slip. Method: take out the spring, grind the box wall or use a special spring oil. (9) followed by feet and five joints such as some car errors leading to a lack of strength, not the normal operation. Methods: by foot to the proper position adjustment. these questions are checked out and ruled out, and then the test machine test, the average value of all measured data in standard value, that watch can accurate operation, finally if the automatic mixing table, can be placed in the multi position test machine test, understand the multi-faceted test. Time is running precision, and understand the table of the automatic mixing is no problem. All procedures are passed, will be accomplished.