服务中心已遍及华北、华东和华南等地区。主要负责百达翡丽、爱彼、江诗丹顿、芝柏、宝玑、宝珀、朗格、劳力士、积家、卡地亚、欧米茄、万国、浪琴等国内外大小五十多个手表品牌的售后维修工作.专业的维修技术、透明的维修价格、当面检测维修定价、立等可取的维修效率。电话预约可享9折优惠！专业专注，专心服务!让时间鉴定品质!瑞亨名表维修中心，您身边的手表养护专家!

　　________________________________________________________________________________________________________________

　　________________________________________________________________________________________________________________

　　条盒轮补齿还相对算比较容易，因为它还是比较“大”的，但是补齿的方法也有2 种，一种是在断齿的部位开槽，然后贴焊上薄铜板料，再在料上用“篦子挫”挫出一样的齿形来另一种是取和残损的条盒轮差不多的另一个条盒轮的部分，经过磨制和修整，把它再镶贴在需要修理的部位。发条(主要是内圈位置)突然断了，致使条盒轮齿骤然受力而发生断齿，一般会一下折断2~3个齿没有放松发条就去直接拆卸手表的大钢轮。后一种方法也叫“贴齿”，相对简单点，主要是省去了再做开齿的加工，难度大的地方，仅在于把“贴齿”的料正确的对位在补齿缺口位置上，不能有一点点的偏差。基本方法是要先用松香，在条盒轮内已经挫制好的缺口，把哪个用于补齿的料精确对位给粘好，然后再用微量的焊锡(最好是焊锡屑)堆在其上，将条盒轮置于一个小铜板上，放在酒精灯上加热，待焊锡完全融化后，用酒精清洗表面，刮去条盒轮内多余的焊锡，休整齿形和齿根，基本就完成了(见照片)。在许多钟表修理书籍里，介绍“栽尖补齿“的方法也不少，但我还是比较喜欢简单易行的，也同样能解决问题。注意事项:绝对不能用焊锡过多，焊锡也只能涂在条盒内，焊接好了以后也不要休整条盒轮的表面，但可以修整齿形和齿根如果检查发现焊接位置有一点偏移，那都必须返工重来，不能凑合。 box Lunbu teeth also relatively easy, because it is "big", but also the method of repairing tooth has 2 kinds, one is in the position of the broken tooth slot welding, then thin copper material, and then use the same type contusion contusion "tooth to another take the wheel box and damaged another box round almost part of the material, after grinding and dressing, and then put it in need of repair parts mounting. spring (mainly in the position of the inner ring) suddenly broke, resulting in a sudden force of a box of gear teeth and the occurrence of broken teeth, generally will be about to break the 2~3 teeth did not relax to go directly to the demolition of a large steel watch. The latter method is also called the "tooth paste", relatively simple, mainly to do without processing the teeth of the difficult place, only in the "tooth paste" right in para fill tooth gap position, not a little different. The basic method is to use in a box of rosin, has been prepared and wheel gap, which used for accurately feeding teeth to glue, and then use the micro solder (preferably Han Xixie) in the heap, the box is placed in a small round copper plate, put the heating on the alcohol lamp, the solder melted completely clean the surface with alcohol, scraping the barrel in excess solder, the rest of the tooth profile and tooth root, basically completed (see photo). In many watches repair books, introduced "the way to repair teeth" is also a lot, but I still prefer the simple, but also can solve the problem. note: absolutely can not use excess solder, solder only on a box, after the good welding don't rest surface box round, but can trim the tooth shape and tooth root if the inspection found a position of welding point offset, it must rework again, do not.