GL3224 电子元器件 GENESYS/创惟科技 封装QFN-32USB 3.0双/单LUN 记忆卡读卡器控制器

　　DESCRIPTION

　　The GL3224 is a crystal-less USB 3.0 Dual/Single LUN card reader controller, it provides 2 LUNs (Logic Unit Number) which can support various types of memory cards, such as Secure DigitalTM(SD), SDHC, miniSD, microSD (T-Flash), MultiMediaCardTM (MMC), RS-MMC, MMCmicro, MMCmobile, Memory StickTM (MS), Memory Stick DuoTM (MS Duo), High Speed Memory StickTM (HS MS), Memory Stick PROTM (MS PRO), Memory Stick PROTM Duo (MS PRO Duo), Memory Stick PRO-HGTM (MS PRO-HG), MS PRO Micro in one chip. It also supports SDXC and Memory Stick XC high density memory cards (capacity up to 2TB) and high speed SD3.0 UHS-I memory cards.

　　The GL3224 can be configured as single LUN to support e•MMC v4.5, 1/4/8bit data bus, High Speed SDR/ High Speed DDR/ HS200 mode, and it is compatible with e•MMC v5.0.

　　The GL3224 also provide small package QFN32 (5x5mm) to support single LUN: SD3.0 only for extreme small PCBA design

　　The GL3224 integrates a high speed 8051 microprocessor and a high efficiency hardware engine for the best data transfer performance between USB and various memory card interfaces. It supports Serial Peripheral Interface (SPI) for firmware upgrade to SPI Flash Memory via USB port. It also integrates 5V to 3.3V and 3.3V to 1.2V regulators and power MOSFETs which can reduce system BOM cost.

　　FEATURES

　　USB specification compliance

　　- Comply with Universal Serial Bus 3.0 Specification rev. 1.0 (USB 3.0)

　　- Comply with Universal Serial Bus Specification rev. 2.0 (USB 2.0)

　　- Comply with USB Mass Storage Class Specification rev. 1.0

　　- Support USB Mass Storage Class Bulk-Only Transport (BOT)

　　- Support 1 device address and up to 3 endpoints: Control (0) / Bulk Data Read In (1) / Bulk Data Write Out (2)

　　- Support 5 Gbps SuperSpeed, 480 Mbps high-speed, and 12 Mbps full-speed transfer rates

　　Integrated USB building blocks

　　- USB2.0 transceiver macrocell (UTM), Serial Interface Engine (SIE), embedded Power-On Reset (POR)

　　Embedded high speed 8051 micro-controller

　　High efficient DMA hardware engine improves transfer rate between USB and flash card interfaces

　　Support Ssecure DigitalTM v1.0/ v1.1/ v2.0/ SDHC/ SDXC (Capacity up to 2TB)

　　Support Secure DigitalTM v3.01 UHS-I (Ultra High Speed): SDR12/ SDR25/ SDR50/ DDR50/ SDR104

　　Support Secure DigitalTM v5.0

　　Support MultiMediaCardTM (MMC)

　　- MMC specification v3.x/ v4.0/ v4.1/ v4.2

　　- x1/ x4/ x8 bit data bus

　　Support Embedded MultiMediaCard TM (e•MMC)

　　- e•MMC specification v4.3/ v4.4/ v4.5/ v5.0

　　- High Speed SDR/ High Speed DDR/ HS200

　　Support Memory StickTM/ Memory Stick PROTM/ Memory Stick PRO DuoTM/ Memory Stick PRO Duo Mark2TM/ Memory Stick MicroTM (M2)/ Memory Stick PRO-HGTM/ Memory Stick PRO-HG DuoTM/ Memory Stick PRO-HG Duo HXTM

　　- Compliant with Memory Stick Series Specification: MS v1.43, MS PRO v1.05, MS Micro v1.04 (MS HG Micro v1.00), MS PRO-HG Duo 1.03, MS XC Duo v1.00, MS XC-HG Duo v1.00, MS XC Micro v1.00 and MS XC-HG Micro v1.00

　　- Support Read/Write quad data access (512Bytex4) for MS PRO-HG to enhance the transmission rate

　　Support Serial Peripheral Interface (SPI) for firmware upgrade to SPI Flash Memory via USB interface

　　Support operation by either MASK ROM or external FW in SPI Flash Memory

　　On-Chip power MOSFETs for all flash media cards power source

　　On-chip 5V to 3.3V and 3.3V to 1.2V regulator

　　On board 25 MHz Crystal driver circuit

　　Support USB2.0 LPM (Link Power Management)

　　Support USB3.0 LTM (Latency Tolerance Messaging)

　　Support USB3.0 U1/U2/U3 low power link state

　　Pass the USB-IF Test Procedure for SuperSpeed product (TID: 340890039)

　　Pass WHCK (Windows Hardware Certification Kit) test for Windows 8.1 (Submission ID: 1620543)

　　Pass WHCK (Windows Hardware Certification Kit) test for Windows 8 (Submission ID: 1620537)

　　Pass WHQL (Windows Hardware Quality Lab) test for Windows 7 (Submission ID: 1620861)

　　Support two SD3.0 interfaces with UHS-I: SDR12/ SDR25/ SDR50/ DDR50/ SDR104 bus mode

　　Support programmable disable MMC interface

　　Support programmable various LUN (Logic Unit Number): 2 LUNs and 1 LUN

　　Support programmable SSC (Spread Spectrum Clocking), clock rate in SD, MS memory card interface for better EMI test effect.

　　Support programmable LED behavior, Read Only option for specific application

　　Support power-saving mode to disconnect USB bus by card remove for better power management

　　Support selective-suspend for entering suspend mode when data transfer pending after several seconds.

　　Support Over-Current protection mechanism

　　Available in QFN48 pin package (7x7mm) for 2 LUNs: SD3.0/MSPRO-HG and microSD3.0/M2; 1 LUN for e•MMC v4.5/ 8bit data bus/ HS200 mode; with SPI I/F for FW upgrade.

　　Available in QFN32 pin package (5x5mm), 1 LUN: SD3.0; with SPI I/F for FW upgrade.