焦化厂用LDM-X型溜槽堵塞检测装置制造价格、LDM-X型溜槽堵塞开关、LDM-X型溜槽堵煤开关、防堵煤开关制造厂家最低批发价格

　　LDM-X型溜槽堵塞检测装置能及时防止皮带输送线的混乱状态发生，溜槽堵塞开关是皮带输送机上不可缺少的安全开关。溜槽被输送物堵塞时立刻输出报警信号，立即停止皮带输送机，溜槽堵塞可引起输送物料的堆积或输送机皮带的损坏以及火灾的发生，但溜槽堵塞开关可预防这些事情发生。所以可预防因紧急停止皮带输送线所引起的输送系统的混乱。LDM-X型溜槽堵塞检测装置检测动作力可调整-检测板前端的检测感度可调整到9.8N~14.7N.因此溜槽堵塞开关能够检测出输送料的颗粒由小到块体所以广泛用于皮带输送线上。

　　LDM-X型溜槽堵塞检测装置规格参数:

　　检测力度:9.8N~14.7N（检测板前段）

　　防护等级:IP55

　　接 点:1a+1b

　　接点容量:250V AC 5A

　　质 量:11kg

　　复位类型:自动复位

　　自动复位:双向动作

　　LDM-X型溜槽堵塞检测装置特长:

　　结构简单动作精准-溜槽堵塞开关有摆动形检测板和限位开关组成，安装在溜槽侧壁已开好的长方形口上。当溜槽被输送物料堵塞时，检测板将向外侧倾斜，此时限位开关就会动作Company name: Shandong Zhenhong Explosion-proof Electrical Equipment Co., Ltd.

　　Contact person: Song Shimin

　　Mobile phone number: 1--5--0--5--4--8--5--3--0--5--1

　　Address: Jining City, Shandong Province Rencheng Industrial Park

　　LDM-X型溜槽堵塞检测装置在恶劣环境下也可使用-因使用防尘轴承，即时有灰尘覆盖也不会影响检测板的动作。还有为了防止因结冰引起的事故发生，可选择利用接近开关型和非接触开关的检测板

　　检测动作力可调整-检测板前端的检测感度可调整到9.8N~14.7N.因此溜槽堵塞开关能够检测出输送料的颗粒由小到块体所以广泛用于皮带输送线上。

　　输送物料的比重小（约0..8g/cm以下）以及溜槽的尺寸小的情况下，因检测力度强，有可能生产动作的不稳定

　　Ldm-x type chute blockage detection device can timely prevent the chaotic state of the belt conveyor line. The chute blockage switch is an indispensable safety switch on the belt conveyor. When the chute is blocked by the conveying material, the alarm signal will be output immediately and the belt conveyor will be stopped immediately. The blockage of the chute can cause the accumulation of the conveying material or the damage of the conveyor belt and the occurrence of fire, but the blockage switch of the chute can prevent these things. Therefore, it can prevent the confusion of the conveying system caused by the emergency stop of the belt conveyor line. Ldm-x type chute blockage detection device can adjust the detection action force - the detection sensitivity of the front end of the detection plate can be adjusted to 9.8N ~ 14.7n. Therefore, the chute blockage switch can detect the particles of the conveying material from small to block, so it is widely used in belt conveyor line.

　　Specifications and parameters of ldm-x chute blockage detection device:

　　Detection strength: 9.8N ~ 14.7n (front section of detection plate)

　　Protection grade: IP55

　　Connect Point: 1A + 1B

　　Contact capacity: 250V AC 5A

　　Quality Quantity: 11kg

　　Reset type: automatic reset

　　Automatic reset: bidirectional action

　　Ldm-x chute blockage detection device has the following advantages:

　　The structure is simple and the action is accurate - the chute blockage switch is composed of a swing detection plate and a limit switch, which is installed on the rectangular opening of the side wall of the chute. When the chute is blocked by conveying materials, the detection board will tilt outward, and the limit switch will act

　　Ldm-x type chute blockage detection device can also be used in harsh environment - due to the use of dust-proof bearing, even if there is dust cover, the action of detection plate will not be affected. In addition, in order to prevent accidents caused by icing, the detection board of proximity switch and non-contact switch can be selected

　　The detection action force can be adjusted - the detection sensitivity of the front end of the detection plate can be adjusted to 9.8N ~ 14.7n. Therefore, the chute blocking switch can detect the particles of the conveying material from small to block, so it is widely used in the belt conveyor line.

　　When the specific gravity of conveying material is small (about 0.8g/cm or less) and the size of chute is small, the production action may be unstable due to strong detection