厂家直销 USB连接器,移动电源蓝牙耳机连接器,迷你USB母座

名称:厂家直销 USB连接器,移动电源蓝牙耳机连接器,迷你USB母座

供应商:东莞市韩晶电子有限公司

价格:面议

最小起订量:1/

地址:桥头镇田新第二工业区60号

手机:13712896873

联系人:陈溪煌   (请说在中科商务网上看到)

产品编号:151833239

更新时间:2019-12-16

发布者IP:

详细说明

  '

  �0�5�1�0 style="TEXT-ALIGN: left" align=left>

  This specification covers the USB CONNECTOR DIP OR SOLDER TYPE

  [本规范适用于USB CONNECTOR DIP OR SOLDER TYPE ]

  2.[产品料号及产品名称] PRODUCT NUMBER AND PART NAME

[产品品名] Product Name[产品料号] Product Number

  3.[构造&组成零件] CONSTRUCTION & COMPONENTS

  [依照工程图] Based on construction drawing

  4.[标准额定值] RATINGS

[项目] Item[规格] Standard
[额定电压] Rated voltage30V AC rms Max.
[额定电流] Rated current1.5A Min
[使用温湿度环境] Operating temperature-30℃~+85℃, 85% RH Max
[储存温湿度环境] Storage temperature-40℃~+60℃, 85% RH Max

  5. [试验条件] TEST CONDITION

  [除非特别说明之外,一般试验及测理将于温度15~35℃,相对湿度25~85%,大气压力86~

  106kPa之条件下完成,但若于上述条件下有任何影响判定值的疑虑,可考量在温度20±2℃,相

  对湿度60~70%,大气压力86~106kPa之条件下完成试验

  The test and measurement,unless otherwise specified,shall be carry out at atemperature of 15 to 35℃,Relative humidity of 25 to 85%,and atmospheric of 86 to 106kPa.However,when any doubt arises on the judgment value it,the test and measurement

  shall be carry out at a temperature of 20±2℃,relative humidity of 60 to 70%,and atmospheric pressure of 86 to 106Pa.

[外观:经目视观察,外观不可有变形,电镀脱落等会降低其功能的异常现象,也不可有严重破裂,刮伤或污损之缺点.Appearance:By looking,there shall not be any abnormality such as deformity,exfoliation of plating,ETC,which can reduce performance,No defect such as cracks scratchs or blemishes.

  6.[电气特性] ELECTRICAL EFFICIENCY

编号NO.项目/Item试验方法/Test Method性能要求/Requirement
6.1[额定电流]ContactCurrent Rating[于室温25℃下施加250V AC电压测试]Measured at an ambient temperature of 25℃,applied 250VAC test.1.5A Min.
6.2AppliedVoltage Rating[额定电压]30V AC(RMS.) continuous maximum,on any signal pin withrespect to the shield.[在任一端子与端子,端子与外壳间施加最大电压30V AC测试]No Breakdown无击穿
6.3ContactResistance[接触阻抗]Mate connectors,Measure by dry circuit,20mV Max,100mA[公母对插后测试]30mΩMax
6.4[绝缘阻抗]InsulationResistance[公母不对插,对相邻端子施加500V DC电压测试]Unmated connectors, apply 500V DC between adjacentterminal or ground.1000MΩMin
编号NO.项目/Item试验方法/Test Method性能要求/Requirement
6.5[耐电压]WithstandingVoltage[公母对插前对各端子施加500V AC电压持续1分钟测试.]Unmated connectors, apply 500V AC for 1 minute between adjacent terminal or ground.No Breakdown and Current loss:1mA Max.无击穿且漏电流≤1mA

  '